Now select all of your objects, go to the render menu, then select set NURBS tessellation , set curvature tolerance to highest quality, U and V around 5000 , click set and close then render it, then you will have this cute looking object (pic 12).

選擇你所有的物體，進入到全局渲染里，設置 NURBS tessellation , 將 curvature tolerance 高為更高組另， U 和 V 取到 5000, 然后 set and close 并渲染它，這樣我們得到如 (pic 12) 的物體 .

pic 12

Wheee...everything is so easy and so smooth with Maya isn't it ?, But oops...this is just part 1. :(
Note : You could put logo there or do whatever you want, more detail or something... :)

喔 ....Maya 是否很簡單 ? 不要急，以上只是第一節 :(
注意 : 你可以在這里放上你喜歡的標記 , 或者刻畫更多的細節 .... :)

Now select all these objects, group them and name the group "rotator", and then save this file as "rotator_gear.mb" or do whatever you like with the file name. :)

現在選擇你所有的物體，并將它們成組，將組命名為 "rotator", 并存儲文件為 "rototor_gearmb"( 也可以是你想用的名字 )

Create Bottom Seat Upholstery

制作椅子的扶手

From side view, create 2 profile curves like in this image (pic 13), then from front view, create a NURBS circle with 18 sections, rotate it 90°, then adjust the CV's with the scale and move tools until it looks like in this image (pic 14).

在側視窗，創建兩條輪廓曲線 (pic 13), 回到前視窗，再創建一條 Nurbs 圓形曲線 (section 18), 旋轉 90 度，然后調整它的各 CV 點到像 (pic 14) 所示 .

pic 13


pic 14

Here's the perspective view

這是透視圖

Then duplicate this curve and rescale it (y axis), move it many times (following the shape of the profile curve) until it looks like this (pic 14). Note : you must rescale the start and end curves very small (pic 15).

然后復制一些曲線并在 y 軸方向上放大或縮小它們，調整到如 (pic 14). 記住 : 最開始和結束的曲線你要盡量將其縮到最小 .(pic 15)

pic 14


pic 15

Then select these 3 curves (pic 16), select a couple of the top CV's and then move them to the left a little bit and rotate them also to the left (pic 17).

選擇這 3 條曲線 (pic 16), 將它們的一些 CV 點向左移動并消微放大一點 (pic 17).

pic 16


pic 17

Now select all these curves from star t to end (not the profile) and then surface > loft . You will have this new object (pic 18), now duplicate mirror this new object with the parameters shown here (pic 19).
Note : The Translate value could be different, but Scale -1 is a must for mirror duplicate :)

現在依此選擇這些曲線（不含那條輪廓線 ) 然后 surface > loft . 你將得到一個曲面如 (pic 18), 接著以鏡像的方式復制這個物體，復制的選項請看 (pic 19).
注意 : 移動 (translate) 的數值可以有所不同，但是拉伸 (scale) 的數值為 -1 時表示以鏡像的方式復制 .

Pic 18



pic 19

OK now you have two of these 2 mirrored objects right ? (pic 20) Next, do the same steps (using duplicated curves) to create the center top and bottom upholstery (pic 21). Remember to use very small curves for the start and end curves. :)
Note : if you want to close the start or end curves, you could also use surface > planar .

OK, 現在你有兩個物體對嗎 ?(pic 20), 接下來要做的是，使用相同的方法 ( 復制 ) 來創建中間的一些曲線 (pic 21). 記住最開始和最后的曲線要縮到最小 .